0.00 EUR
Reģistrēties

CROWN XTi2002

800W @ 4ohm, Peak limiter, fan mode control, HiQnet control, XTi 2 Series
Akcija!
Cena:
1019.00 EUR
RRP cena:
1203.00 EUR
Ietaupījums:
364.00 EUR (30%)
Cena ar PVN 21% bez piegādes
CROWN
Ražotājs: CROWN
ID:
480401050
Ražotāja garantija:
3 gadi
Vērtējums:
Lai vērtētu produktu, nepieciešams pieslēgties sistēmai
Informācija
Tehniskā specifikācija

 XTi

There's no debate – when you choose Crown's XTi 2 Series, you're choosing one of the most powerful and innovative amplifiers on the market today. That's because the all-new XTi 2 Series amps continue to set the standard for unmatched performance and value, delivering the goods night after night without breaking a sweat.
 
NEXT GENERATION FEATURES :
  • Peakx Plus™ Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release
  • Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning
  • 3 User-defined fan mode controls – normal, early and fullspeed – for matching fan performance to a specific application
  • New system monitoring provides software visibility of AC line voltage and power supply temperature
  • Integrated cast-aluminum handles for easy handling and enhanced durability
  • Locking power cord clip provides a secure connection between the amplifier and power cord
  • Updated HiQnet System Architect™ control software
  • Increased number of presets to a total of 50; 49 of which are user definable
 
 POWER SPECIFICATIONS :
2Ω Stereo (per ch.) 1000W
4Ω Stereo (per ch.) 800W
8Ω Stereo (per ch.) 475W
8Ω Bridge-Mono 1600W
4Ω Bridge-Mono 2000W
 
INTEGRATED PROCESSING
Input EQ : 6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed.
 
Crossover Filters : Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ± 15 dB bandpass gain and polarity control.
 
Output EQ : 8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed.
 
Delay : For signal alignment of driver; 50 mS of total delay.
 
SubHarmonic Synth : Takes the low-frequency content of the input signal and "synthesizes" a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type.
 
Peakx™ Plus Limiter : User defeatable limiter that allows users to control Threshold, Attack, and Release times.
 
Presets : 50 total presets, 49 of which are user-definable.
 
PERFORMANCE
Sensitivity (for full rated power at 4 ohms) : 1.4 Vrms
Frequency Response (at 1 watt, 20 Hz - 20 kHz) : +0 dB, –1 dB
Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms) : 100 dB (A weighted)
Total Harmonic Distortion (THD) : < 0.5%
Damping Factor 20 Hz to 1 kHz : > 500
Crosstalk (below rated power) : 20 kHz - 1 kHz: > 70 db
Input Impedance (nominal) : 20k ohms balanced, 10k ohms unbalanced
Maximum Input Signal : +22 dBu typical
AC Line Voltage and Frequency Configurations : 100 VAC, 120 VAC, 220-240 VAC 50/60 Hz
AC Line Current (120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch)
 
XTi1002: 6.8A; no more than 38W at idle
XTi2002: 8.3A; no more than 38W at idle
XTi4002: 10.5A; no more than 38W at idle
XTi6002: 15.3A; no more than 180W at idle
 
Operating Temperature : 0°C to 40°C at 95% relative humidity (non-condensing)
 
CONTROLS
Level : Two front-panel rotary level controls, one for each channel
Power Switch : On/Off switch applies AC power to the amplifier
Sel/Prev/Next Buttons : Three buttons near the LCD screen that are used to access menu items and front panel lockout
LCD Screen : Backlit liquid crystal display that shows preset and processing status
 
INDICATORS
Signal Indicator : Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).
–10 Indicator : Green LED flashes when output signal exceeds -10 dB below clip.
–20 Indicator : Green LED flashes when output signal level exceeds -20 dB below clip.
Ready Indicator : Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
Clip Indicator : Red LED, one per channel, turns on at the threshold of audible distortion
Temp Indicator : Red LED, one per channel, illuminates under excessive temperature conditions
Power Indicator : Blue LED illuminates when the amplifier has been turned on and has power
 
INPUT/OUTPUT CONNECTORS
Input Connectors : XLR, one per channel
Link/Out Connector : Loop-thru signal from input connector for linking another amplifier, one per channel.
Output Connectors :Two Neutrik® Speakon® NL4MP output connectors. Channel-1 Speakon® is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors).
HiQnet™ USB Connector : Type B, connects to HiQnet™ network.
 
CONSTRUCION
Chassis : Steel
Front Panel : Cast-aluminum
Cooling : Proportional speed fan with front-to-rear airflow.
Dimensions :19" (W) x 3.5" (H) x 12.25" (D)

Net Weight : 18.5 lbs (8.4kg) 

Saraksts ir tukšs
    captcha